Solid state DC switch 70V / 4A

- Operating voltage 8-70VDC, max. load. 4A (see data sheet)
- Switching of DC loads up to 70V/4A with low power (>3.3V >30uA)
- Use with lithium BMS for charge/discharge control
- Can also be used for switching alternators.

CAN patch cable - 0.6m (M/M)

- M12 5-pin micro style connector (NMEA2000)
- IP68, gold contacts, cable length: 0.6m
- for connecting Nomia and Nomada Super-B batteries

CAN / NMEA2000 patch cable - 1m (M/W)

- M12 5-pin micro style connector (NMEA2000)
- IP68, gold contacts, cable length: 1m

CAN / NMEA2000 patch cable - 5m (M/W)

- M12 5-pin micro style connector (NMEA2000)
- IP68, gold contacts, cable length: 5m

Lynx Smart BMS (M8) for Victron lithium batteries

- Battery voltage 12-48V, max. current 600A
- Battery monitor, BMS, main relay,
- VE.Can interface (NMEA2000 capable), Bluetooth

Touch display for Cerbo GX

- High-resolution touch display
- 7 inch, resolution: 1024 x 600

- HDMI & USB

LTE modem & GPS add-on device for GX devices

- for connecting GX devices to the VRM portal
- 8-70VDC power supply
- incl. LTE antenna (SIM card required)
- connection for GPS antenna (not included)

AC 3-phase electricity meter

- for AC alternating current measurement of
generators, consumers, PV or for ESS
- 3 phases, Ethernet interface, display

AC 3-phase electricity meter

- for AC alternating current measurement of
generators, consumers, PV or for ESS
- 3 phase, RJ485 interface

RS485 to Zigbee converter & transceiver

- For wireless connection of a netmeter
to a Cerbo GX, requires counterpart
- Transmits, receives and converts the Zigbee signal

USB to Zigbee converter & transceiver

- For wireless connection of a netmeter
to a Cerbo GX, requires counterpart
- Transmits, receives and converts the Zigbee signal

CAN patch cable right-angled - 0.25m (M/W)

- M12 5-pin micro style connector (NMEA2000)
- IP68, gold contacts, cable length: 0.25m
- for connecting Nomia and Nomada Super-B batteries

Current transformer 100A - 10m

- Measuring range: 100 A / 50 mA for MultiPlus-II / MultiGrid-II
- Cable length: 10m

Battery Interface Box Super-B 12V - 350A

- connects several Super-B batteries together
- with integrated load relay and pre-charging
- button for ON / OFF / Reset

Smart BMS 12V / 100A / 200A

- Vehicle charging limit 100Amp, system current 200Amp
- Outputs to control charging / discharging
- Remote, alarm contacts, Bluetooth, status LEDs

CAN / NMEA2000 patch cable - 10m (M/W)

- M12 5-pin micro style connector (NMEA2000)
- IP68, gold contacts, cable length: 10m

CAN / NMEA2000 patch cable - 2m (M/W)

- M12 5-pin micro style connector (NMEA2000)
- IP68, gold contacts, cable length: 2m

CAN cable Y-split right-angled male to straight (W&M)

- M12 5-pin micro style connector (NMEA2000)
- IP68, cable length: 0.2m

RuuviTag 3M VHB adhesive

- for easy installation of RuuviTag sensors
- High-quality 3M VHB adhesive tape
- 40 x 0.65mm

RuuviTag stand

- for optimal positioning of RuuviTag sensors
- improved measurement & range
- 55 x 27.74 x 18.44mm

RuuviTag Bag / Pouch

- Fabric bag with zip & velcro
- easy to carry
- length of fastening strip 3cm

AC 3-phase electricity meter

- for AC alternating current measurement of
generators, consumers, PV or for ESS
- 3 phases, RJ485 interface, display

Tank sensor for Cerbo GX - 20cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 20cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 22cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 22cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 25cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 25cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 28cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 28cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 30cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 30cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 32cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 32cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 17cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 17cm,
- 5 hole mounting flange 69 / 38mm

Tank sensor for Cerbo GX - 15cm

- Resistance sensor 10/180Ohm
suitable for Victron Cerbo GX
- shaft length 15cm,
- 5 hole mounting flange 69 / 38mm