Ekrano GX system control display

- 7-inch display with integrated GX controller
- 2 VE.Bus, 3 VE.Direct, 4 VE.Can
- 2 USB, LAN, MicroSD, 2 WIFI
- 2 digital, 3 tank, 2 temp inputs, 2 relays

Touch display for Cerbo GX

- High-resolution touch display
- 5 inch, resolution: 800 x 460
- HDMI & USB

Touch display for Cerbo GX

- High-resolution touch display
- 7 inch, resolution: 1024 x 600

- HDMI & USB

Cerbo GX system monitoring

- 2 VE.Bus, 3 VE.Direct, 2 Ve.CAN, 2 CanBMS
- 2 USB, HDMI, LAN, MicroSD, 2 WIFI
- 4 digital, 4 tank, 4 temp inputs, 2 relays

Cerbo GX MK2 system monitoring

- 2 VE.Bus, 3 VE.Direct, 3 USB, HDMI
- 2x 2 Ve.CAN (CAN BMS capable isolated)
- MicroSD, 2 WIFI, LAN
- 4 digital, 4 tank, 4 temp inputs, 2 relays
- customised RJ45 ports

Cerbo GX-S system monitoring

- 2 VE.Bus, 3 VE.Direct, 2 Ve.CAN, 4 digital inputs
- 2 USB, HDMI, LAN, MicroSD, 2 WIFI, 2 relays
- without CanBMS, Tank & Temp inputs

GX Tank 140 Interface

- 4 tank level sensors, 4-20mA / 0-10V
- for connection to Cerbo GX
- upper and lower limit values adjustable

Ve.Bus Smart Bluetooth interface

- to monitor operation
- ON / OFF / Charger only, set shore power limit
- Voltage and temperature sensor for charger

Ve.Direct to Bluetooth interface

- for programming and monitoring
from VE.Direct devices without Bluetooth
- with VictronConnect App mobile

Global Link remote monitoring

- Remote monitoring VRM via 4G LTE-M, SIM incl. (4 years)
- 2 VeDirect & up to 25 compatible Bluetooth devices
- 2 digital inputs, relay output

Venus GX system monitoring (obsolete)

- 2 VE.Bus, 2 VE.Direct, 2 Ve.Can, 1Can
- 2 USB, LAN, MicroSD,2 WIFI, NO display
- 3 tank, 3 temp inputs, 2 relays

Ve.Direct to USB interface

- for programming and monitoring
from VE.Direct devices
- for expanding VE.Direct connections on GX devices

AC 1-phase electricity meter

- for AC alternating current measurement of
generators, consumers, PV or for ESS
- 1 phase, RJ485 interface

AC 3-phase electricity meter

- for AC alternating current measurement of
generators, consumers, PV or for ESS
- 3 phases, Ethernet interface, display

Smart Battery Sense

- Wireless battery voltage & temperature sensor
for Victron MPPT solar controllers and various chargers.
- range approx. 10m

Small BMS Victron Lithium battery management

- controls charge / discharge relay (10mA / 1mA)
- pre-alarm relay & system ON / OFF
- no VE.Bus control

VE.BUS BMS Victron Lithium battery management

- controls MultiPlus & Quattro's
- controls charge / discharge relay (2A / 10mA)
- pre-alarm relay & system ON / OFF

4-way distributor plus & minus for MEGA fuses

- System voltage 12-48V, maximum current 1000A
- M8 connections, for 4 MEGA fuses
- Connection of plus & minus, with cover cap,
- suitable for Lynx BMS 500

CAN Bus USB Interface

- for connecting Can.Bus devices to a PC

Temperature sensor for Buck Boost

- controls charging of Buck Boost if temperature is too low
- CAN interface for Prog. & Buck Boost connection
- Temperature sensor can also be used for MultiPlus via switching contact

Lynx battery monitor with fuse

- Battery voltage 12-48V, maximum current 1000A
- Connections M8 (Lynx modules), without CNN fuse
- Interface VE.Can (NMEA2000 capable)

Wifi USB dongle for colour control

- USB ModMyPi Wifi Dongle
- 2.4G Wireless max. 150 Mbps

VE.CAN to CAN Bus BMS Cable - Type B

- Cable to connect a CAN bus BMS capable battery
to Victron - 5m
- 2 options available

VE.CAN to CAN Bus BMS cable - Type A

- Cable to connect a CAN bus BMS capable battery
to Victron - 5m
- 2 options available

LTE modem & GPS add-on device for GX devices

- for connecting GX devices to the VRM portal
- 8-70VDC power supply
- incl. LTE antenna (SIM card required)
- connection for GPS antenna (not included)

AC 3-phase electricity meter

- for AC alternating current measurement of
generators, consumers, PV or for ESS
- 3 phase, RJ485 interface

RS485 to Zigbee converter & transceiver

- For wireless connection of a netmeter
to a Cerbo GX, requires counterpart
- Transmits, receives and converts the Zigbee signal

USB to Zigbee converter & transceiver

- For wireless connection of a netmeter
to a Cerbo GX, requires counterpart
- Transmits, receives and converts the Zigbee signal

RS485 to USB converter

- For connecting a netmeter to
a Cerbo GX
- 1.8m cable